Sony DVD RW DRU-810A

Sony DVD RW DRU-810A was working fine, until this afternoon when it decided it wont read any cd-r/dvd-r, i was worried so i upgraded its firmware, much to my dismay, it still doesnt work

Actually it reads the CD, but once it starts to burn it stays on 5% and stops then errors, and i tried alcohol120, not working :3

Here is the log btw

Liquid_Snack

1C82-0000-19E5-MAAX-4005-5321-****

Windows XP 5.1
IA32
WinAspi: -

NT-SPTI used
Nero Version: 7.8.5.0
Internal Version: 7, 8, 5, 0

Recorder: <SONY DVD RW DRU-810A> Version: 1.0f - HA 1 TA 3 - 7.8.5.0
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <TP3235T VPR118Z >Version: 1.0 - HA 1 TA 1 - 7.8.5.0
Adapter driver: <SCSI> HA 1

=== Scsi-Device-Map ===
CdRomPeripheral : SONY DVD RW DRU-810A atapi Port 2 ID 0 DMA: On
DiskPeripheral : WDC WD800BB-00JHC0 atapi Port 3 ID 0 DMA: On
DiskPeripheral : Hitachi HDS721680PLAT80 atapi Port 3 ID 1 DMA: On
CdRomPeripheral : TP3235T VPR118Z 1.0 azarj4x1 Port 4 ID 0 DMA: Off

=== CDRom-Device-Map ===
SONY DVD RW DRU-810A E: CDRom3
TP3235T VPR118Z F: CDRom1
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 74448896 (0) Byte
BUFE : 0
Physical memory : 510MB (522668kB)
Free physical memory: 166MB (170204kB)
Memory in use : 67 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

20.5.2007
CueSheet
6:54:06 PM #1 Text 0 File SCSIPTICommands.cpp, Line 411
LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL

6:54:07 PM #2 Text 0 File Burncd.cpp, Line 3187
SONY DVD RW DRU-810A
Power-Burn activated

6:54:07 PM #3 Text 0 File Burncd.cpp, Line 3499
Turn on Disc-At-Once, using CD-R/RW media

6:54:07 PM #4 Text 0 File DlgWaitCD.cpp, Line 307
Last possible write address on media: 359848 ( 79:59.73)
Last address to be written: 309403 ( 68:47.28)

6:54:07 PM #5 Text 0 File DlgWaitCD.cpp, Line 319
Write in overburning mode: NO (enabled: CD)

6:54:07 PM #6 Text 0 File DlgWaitCD.cpp, Line 2949
Recorder: SONY DVD RW DRU-810A;
CDR code: 00 97 24 16; OSJ entry from: SONY Corporation
ATIP Data:
Special Info [hex] 1: D0 00 A0, 2: 61 18 10 (LI 97:24.16), 3: 4F 3B 4A (LO 79:59.74)
Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 00 00 (invalid)

6:54:07 PM #7 Text 0 File DlgWaitCD.cpp, Line 493
>>> Protocol of DlgWaitCD activities: <<<
=========================================

6:54:07 PM #8 Text 0 File ThreadedTransferInterface.cpp, Line 793
Setup items (after recorder preparation)
0: TRM_DATA_RAW_MODE2 (Cue Sheet Track)
2 indices, index0 (150) provided
original disc pos #0 + 309404 (309404) = #309404/68:45.29
relocatable, disc pos for caching/writing not required/not required
-> TRM_DATA_RAW_MODE2, 2352, config 0, wanted index0 0 blocks, length 309404 blocks [E: SONY DVD RW DRU-810A]
--------------------------------------------------------------

6:54:07 PM #9 Text 0 File ThreadedTransferInterface.cpp, Line 995
Prepare [E: SONY DVD RW DRU-810A] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x20; Session Closed, disc fixated
Tracks 1 to 1: Idx 0 Idx 1 Next Trk
1: TRM_DATA_RAW_MODE2, 2352/0x00, FilePos 0 352800 728071008, ISRC ""
DAO layout:
===========
___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|__ ____NWA_|_RecDep__________
-150 | lead-in | 0 | 0x41 | 0 | 0 | 0x00
-150 | 1 | 0 | 0x41 | 0 | 0 | 0x00
0 | 1 | 1 | 0x41 | 309404 | 0 | 0x00
309404 | lead-out | 1 | 0x41 | 0 | 0 | 0x00

6:54:07 PM #10 Text 0 File SCSIPTICommands.cpp, Line 209
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME

6:54:07 PM #11 Text 0 File Burncd.cpp, Line 4278
Caching options: cache CDRom or Network-Yes, small files-No (<64KB)

6:54:07 PM #12 Phase 24 File dlgbrnst.cpp, Line 1762
Caching of files started

6:54:07 PM #13 Text 0 File Burncd.cpp, Line 4397
Cache writing successful.

6:54:07 PM #14 Phase 25 File dlgbrnst.cpp, Line 1762
Caching of files completed

6:54:07 PM #15 Phase 36 File dlgbrnst.cpp, Line 1762
Burn process started at 16x (2,400 KB/s)

6:54:07 PM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2721
Verifying disc position of item 0 (relocatable, no disc pos, no patch infos, orig at #0): write at #0

6:54:07 PM #17 Text 0 File MMC.cpp, Line 17654
StartDAO : CD-Text - Off

6:54:07 PM #18 Text 0 File MMC.cpp, Line 22344
Set BUFE: Power-Burn -> ON

6:54:07 PM #19 Text 0 File MMC.cpp, Line 17882
CueData, Len=32
41 00 00 34 00 00 00 00
41 01 00 21 00 00 00 00
41 01 01 21 00 00 02 00
41 aa 01 34 00 44 2f 1d

6:54:07 PM #20 Text 0 File ThreadedTransfer.cpp, Line 269
Pipe memory size 74390400

6:55:04 PM #21 SPTI -1135 File SCSIPassThrough.cpp, Line 179
CdRom3: SCSIStatus(x02) WinError(0) NeroError(-1135)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x0C
Sense Qual: 0x00
CDB Data: 0x2A 00 FF FF FF 6A 00 00 1B 00 00 00
Sense Area: 0x70 00 03 00 00 00 00 12 00 00 00 00 0C
Buffer x06b379c0: Len xf810
0x00 FF FF FF FF FF FF FF FF FF FF 00 00 00 00 02
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

6:55:04 PM #22 CDR -1135 File Writer.cpp, Line 303
Write error
E: SONY DVD RW DRU-810A

6:55:04 PM #23 Phase 38 File dlgbrnst.cpp, Line 1762
Burn process failed at 16x (2,400 KB/s)

6:55:04 PM #24 Text 0 File SCSIPTICommands.cpp, Line 254
SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME

6:55:06 PM #25 Text 0 File Cdrdrv.cpp, Line 11214
DriveLocker: UnLockVolume completed

6:55:06 PM #26 Text 0 File SCSIPTICommands.cpp, Line 411
UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL


Existing drivers:

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)



Help please~

Jam it back in, in the dark.

I think your DVD driver need to clean lens laser & what last firmware you upgraded?is (1.0f)

There's nowhere I can't reach.

Yeah, apparently when i try to burn something, it gives me taht wierd spinning sound so :3

Most amazing jew boots

It's busted. Buy a new one!

I am a dolphin, do you want me on your body?

I WILL! <3

I might look for a good burner at HK tommorow so...

I was speaking idiomatically.